如题所述
第1个回答 2017-07-19
1.前几天刚买的一款Realtek RTL8191SU 的无线网卡，进到虚拟机后想用airmon-ng把网卡切为监听模式但是就会出现（由于图片老是上传失败这里直接复制）
root@kali:~# airmon-ng start wlan0
Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!
PID Name
3669 dhclient
3734 NetworkManager
4163 wpa_supplicant
PHY Interface Driver Chipset
null wlan0 r8712u Realtek Semiconductor Corp. RTL8191SU 802.11n WLAN Adapter
2.用iwconfig命令确定网卡已经被虚拟机识别并加载
root@kali:~# iwconfig
eth0 no wireless extensions.
wlan0 unassociated Nickname:"rtl_wifi"
Mode:Managed Access Point: Not-Associated Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lo no wireless extensions.
3.然后用尝试用iwconfig wlan mode monitor将网卡切到监听模式，然而
root@kali:~# iwconfig wlan0 mode monitor
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
ps：用iwconfig wlan0 mode ad-hoc/master 能成功将网卡切到adhoc模式和路由器模式
root@kali:~# airmon-ng start wlan0
Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!
PID Name
3669 dhclient
3734 NetworkManager
4163 wpa_supplicant
PHY Interface Driver Chipset
null wlan0 r8712u Realtek Semiconductor Corp. RTL8191SU 802.11n WLAN Adapter
2.用iwconfig命令确定网卡已经被虚拟机识别并加载
root@kali:~# iwconfig
eth0 no wireless extensions.
wlan0 unassociated Nickname:"rtl_wifi"
Mode:Managed Access Point: Not-Associated Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lo no wireless extensions.
3.然后用尝试用iwconfig wlan mode monitor将网卡切到监听模式，然而
root@kali:~# iwconfig wlan0 mode monitor
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
ps：用iwconfig wlan0 mode ad-hoc/master 能成功将网卡切到adhoc模式和路由器模式
第2个回答 2017-07-19
从早到弄到现在，啥驱动都试了，就是不行。其它三个模式可以启动。
比如：master ad-hoc managed 就是尼玛 monitor 启动不了。
8191SU试过 MT7601U 的芯片我也试过，都没用。。
比如：master ad-hoc managed 就是尼玛 monitor 启动不了。
8191SU试过 MT7601U 的芯片我也试过，都没用。。
第3个回答 2017-07-19
从早到弄到现在，啥驱动都试了，就是不行。其它三个模式可以启动。
比如：master ad-hoc managed 就是尼玛 monitor 启动不了。
8191SU试过 MT7601U 的芯片我也试过，都没用。。
比如：master ad-hoc managed 就是尼玛 monitor 启动不了。
8191SU试过 MT7601U 的芯片我也试过，都没用。。
