车刀 纵向 横向 螺纹 手柄 键槽 正转 反转 轴承 螺丝 扳手 钳子 松开 精度 测量 长度 高 宽 直径 机械 轴 套 液压 转速 速度 汽缸 活塞 连杆 曲轴 仪表 拖板 螺栓 螺母 启动 停止 平行 垂直 水平 调整 负荷 移动 快速 慢速 计算 基准 参考 螺距 导程 半径 误差 冲压 铸造 车床 铣床 磨床 钻孔 材料 按键 按扭 显示 报警 液面 手动 制动 自动 电池 升 降 外圆 机壳 机架 床身 立柱 功率 齿条 油杯 油箱 密封 叶泵 定子 转子 绕组 电源 频率 脉冲 电压 电源 电阻 电容 电感 光栅 光电 温度 过载 台阶 配合 短路 触点 闭合 断开 吸合 释放 床鞍 尾座 顶尖 冷却 排屑 运输 电缆 插头 误差 声音 故障 振动 交流 直流 正向 反向 定位 快进 快退 位置 距离 上料 卸料 推出 缩回 挡铁 抬起 落下 循环 暂停 程序 释放 关闭 缓冲 确认 输出 信号 红色 黑色 绿色 白色 黄色 清零 复位 钳工 干燥 清洁 延时 功能 指令 辅助 顺序 闭环 开环 串联 编程 保存 存储 通信 圆弧 软件 数控 网络 灰尘 更换 导线 材料 联动 换刀 刀库 刀臂 行程 低速 地址 转速 选择 系统 界面 异常 删除 设定 编辑 帮助 切换 取消 翻页 换挡 输入 信息 图形 手轮 监视
主轴箱 操作盘 断路器 计数器 电器柜 润滑油 光洁度 工作台 千斤顶 摩擦力 主动轮 离合器 电磁铁 从动轮 压力机 起重机 单向阀 工作台 液压缸 控制阀 换向阀 电动机 传感器 熔断器 进给箱 摩擦片 照明灯 继电器 接触器 基准面 中心线 输送机 计算机 打印机 分辨率 机械手 分度台 坐标系 旋转轴 皮带轮 参数表 程序头 程序尾 滚珠丝杠 加工精度 压缩空气 螺纹导程 额定电流 操作手柄 电源开关 行程开关 输送装置 空气不足 润滑不足 电池不足 单向负载 直线进给 定位误差 重复定位 固定循环 程序开始 程序结束 倍率选择 绝对坐标 相对坐标 报警履历 报警显示 信息显示 程序显示 程序检查 进给保持 表面粗糙度 刀具长度补偿 刀具半径补偿 交换工作台 当前程序段 程序再启动 输入值超过了允许范围 交换齿轮箱 刀具路径图 用户宏程序 格式不正确 输入无效
The headstock control panel circuit breaker counter apparatus cabinet lubricating oil smooth finish work table hoisting jack friction force driving pulley coupling electro-magnet driven wheel press hoist crane cone-way valve work table hydraulic cylinder control valve cross valve electric motor sensor fuse gear box friction disk flare relay contact device reduced plane middle line conveyer computer printer resolution manipulator circular dividing table coordinate system rotation axis belt pulley parameter list procedure procedure tail ball bearing guide screw processing precision compressed air thread leads the nominal current operation handle power switch limit switch feedway air insufficient lubrication insufficient battery insufficient unidirectional load straight line to feed position error to duplicate the localization fixed cycle procedure to start the procedure conclusion percentage choice absolute coordinate relative coordinates to report to the police the personal history to report to the police the displayed information to demonstrate the program display program check to feed maintenance surface roughness cutting tool length compensation cutting tool radius compensation exchange work table current segment procedure started the input value to surpass the permission againThe scope exchange gear box cutting tool path diagram user great procedure form inputs not correctly invalid